MOTOR STEERING CONTROL WIRING METHODS: you can switch control can also be connected to the MCU control, to GND in then in 5V. NOTE: Due to different motor manufacturers to make the hall of hall line order does not necessarily follow the line on the board to match the sequence, need to be adjusted, please parents who pay attention! If the line sequence wrong, does not boot properly, current, or start other phenomena not open, forced to use the drive plate will burn!!! THE MOTOR SPEED CONTROL WIRING METHODS: available potentiometer system speed can also be connected to the MCU control, when the potentiometer control wiring, the potentiometer middle pin is connected to VR speed port, potentiometer connected to both ends of 5V and GND terminal voltage more high speed OPERATING VOLTAGE: DC 12V-36V. Electrical wiring methods: Brushless DC motor for the three lines, corresponding /U,MB/V,MC/W PULSE SPEED : high and low output . IC can not understand the information with the customer request. Specification:
Operating voltage: DC 12V-36V
Operating Current: <=15A
Driver Power: <=500W
Speed Voltage: 0.1V-5V
Operating Temperature:-40-85°C
Humidity: 90%RH
Stall :Yes
Enable Control: Yes
Over-current : Yes
Steering control: Yes
Speed control : Yes
Size: 63*42*17mm(L*W*H); Probe size 3mm,length: fixing hole center distance 57mm; width:fixed hole center distance 36.5mm
Power terminal Out:
VCC(positive power supply)
GND(negative one)
MC(motor phases W)
MB(motor phases V)
(motor phase U)
Set for the control side:
GND control terminal ground
VR the governor end 0-5V(corresponding to 10% of motor speed -100%)
reversing control(connected to 5V or ground can the motor rotation direction)
M tachometer pulse output(depending on the number of motor poles corresponding to the number of pulse per revolution of the output number)
EL enable control terminal(connected to 5V ot ground running then 5V, grounding the motor stops)
5V 5V control terminal
HALL for the hall terminals:
5V Hall power positive
Ha Hall
Hb Hall
Hc Hall
GND Hall negative
Hall inputs for hall:
Wiring diagram is shown, one corresponding to the HA, HB,HC and on the motor, 5V power supply connected to the motor positive, GND power supply negative to the motor hall.
Package Includes:
1 x 12-36V 500W Brushless Motor Controler
Operating voltage: DC 12V-36V
Operating Current: <=15A
Driver Power: <=500W
Speed Voltage: 0.1V-5V
Operating Temperature:-40-85°C
Humidity: 90%RH
Stall :Yes
Enable Control: Yes
Over-current : Yes
Steering control: Yes
Speed control : Yes
Size: 63*42*17mm(L*W*H); Probe size 3mm,length: fixing hole center distance 57mm; width:fixed hole center distance 36.5mm
Power terminal Out:
VCC(positive power supply)
GND(negative one)
MC(motor phases W)
MB(motor phases V)
(motor phase U)
Set for the control side:
GND control terminal ground
VR the governor end 0-5V(corresponding to 10% of motor speed -100%)
reversing control(connected to 5V or ground can the motor rotation direction)
M tachometer pulse output(depending on the number of motor poles corresponding to the number of pulse per revolution of the output number)
EL enable control terminal(connected to 5V ot ground running then 5V, grounding the motor stops)
5V 5V control terminal
HALL for the hall terminals:
5V Hall power positive
Ha Hall
Hb Hall
Hc Hall
GND Hall negative
Hall inputs for hall:
Wiring diagram is shown, one corresponding to the HA, HB,HC and on the motor, 5V power supply connected to the motor positive, GND power supply negative to the motor hall.
Package Includes:
1 x 12-36V 500W Brushless Motor Controler