6 ft USB to TTL serial adapter (with 4 pin 0.1” pitch female header socket) connects devices with 3.3 V logic level UART signals interface to a laptop via USB port A genuine PL2303TA chip module is housed in USB 2.0 type A male terminal for wider compatibility and supports reliable data transfer rates 6 feet USB to TTL serial cable 3V3 (4 way output flying leads ) provides access to UART (transmit) Tx, (receive) Rx, VCC (5V) and GND PL2303 Prolific chipset on the PCB board has configurable internal EEPROM and UART signals can be individually inverted by configuring the EEPROM 4 pin 3.3V USB to TTL converter cord Compatible with Windows 10, 8, 8.1, 7 (32, 64-bit), 2008/XP/Vista/CE; ideal USB 2.0 debug cord for Vendor ID re-write, router, GPS, set top box, transmitter, flash firmware on hard drive, etc. 6-Foot PL2303TA chip USB to TTL serial adapter cable for 3.3 V logic level serial communication (rx, tx, vcc and GND) This USB TLL serial converter is built with Prolific PL2303 chip, FTDI’s royalty-free VCP allow for communication as a standard COM port; a great conversion data cord to meet with your needs of debugging, boot-loading, programming, etc.
NOTE: If any installation or usage issues, please email us or you may download a driver and usage guide on Prolific official website
The original PL2303 chip is embedded in the USB-A end; 4 way 0.1” header connector with GND (ground), VCC (5V), RX and TX at 3V3 logic level.
Applications: Upgrading Legacy Peripherals to USB Interface Microcontroller UART or I/O, FPGA / PLD to USB Industrial Control USB Software / Hardware Encryption Dongles ...
Features - The I/O pins of the USB to serial adapter wire are configured to operate at 3.3V logic level - Entire USB protocol handled by the electronics in the cable; - UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity; - Data transfer rates from 300 to 3M baud rate at TTL levels; - Internal EEPROM with users writable area; - Supply voltage comes from USB bus, no external supply required; - UHCI / OHCI / EHCI host controller compatible
Specific Interface A: USB 2.0 type A Male Port Interface B: 4 pin Female Socket flying leads Chip: Prolific PL2303TA Supports Windows 2008, XP and XP 64-bit, Vista and XP 64-bit, CE 4.2, 5.0 and 6.0; Windows 7, 8, 8.1, 10 (32 and 64-bit);
Cable Colour: Black
Wire Length: 1.8 Meter
What’s Included 1 x USB to Serial TTL Level Converter Cable 6ft 1 X User Manual
NOTE: If any installation or usage issues, please email us or you may download a driver and usage guide on Prolific official website
The original PL2303 chip is embedded in the USB-A end; 4 way 0.1” header connector with GND (ground), VCC (5V), RX and TX at 3V3 logic level.
Applications: Upgrading Legacy Peripherals to USB Interface Microcontroller UART or I/O, FPGA / PLD to USB Industrial Control USB Software / Hardware Encryption Dongles ...
Features - The I/O pins of the USB to serial adapter wire are configured to operate at 3.3V logic level - Entire USB protocol handled by the electronics in the cable; - UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity; - Data transfer rates from 300 to 3M baud rate at TTL levels; - Internal EEPROM with users writable area; - Supply voltage comes from USB bus, no external supply required; - UHCI / OHCI / EHCI host controller compatible
Specific Interface A: USB 2.0 type A Male Port Interface B: 4 pin Female Socket flying leads Chip: Prolific PL2303TA Supports Windows 2008, XP and XP 64-bit, Vista and XP 64-bit, CE 4.2, 5.0 and 6.0; Windows 7, 8, 8.1, 10 (32 and 64-bit);
Cable Colour: Black
Wire Length: 1.8 Meter
What’s Included 1 x USB to Serial TTL Level Converter Cable 6ft 1 X User Manual