[OE Number] JF2-H1950-00, JR3-H1950-00, J38-81950-01. Please check your old solenoid's mounting type and measure the length between mouting holes, to avoid any mounting problem. [Fitment] For Yamaha G11-A Yamahauler 1993-1994 1996-2001, For Yamaha G14-A/G14-E Ultima 1995 1996, For Yamaha G16-A/G16-E Ultima 1996-2002, For Yamaha G2-A/G2-E 1985-1991, For Yamaha G3-A Sun Classic 1986, For Yamaha G3-E Sun Classic 1987, For Yamaha G5-A Sun Classic 1990-1995, For Yamaha G5-E Sun Classic 1990-1992, For Yamaha G6S 1970-1971, For Yamaha G7S 1972, For Yamaha G8-A/G8-EFleet Classic 1990-1994, For Yamaha G9-A/G9-E Fleet Master 1991-1995 [Features] Silver tone tactile point with silver tone body and bottom, 4 terminals include hardware like 5/16-18 (2pcs) and 10-32 (2pcs) threaded studs. The whole body adopt durable zinc-plated steel and 180℃ copper wire, for anti rusting, wear resistance and heat resistance, providing stable performance and longer service life. [Details] Plug and play, bring back your golf cart down to running. The Solenoid starter working transient current is 200A, continuous working current recommends under 100 Amp( continuous duty 12V). Normally use 80A as working current which can effectively extend the service life. [Package] Include 1x Solenoid Starter. Note: not to overtighten the nut/terminal during installation. This is a continous duty solenoid, not a intermittent duty solenoid. OE Number: JF2-H1950-00, JR3-H1950-00, J38-81950-01
Fitment
For Yamaha G11-A Yamahauler 1993-1994 1996-2001
For Yamaha G14-A/G14-E Ultima 1995 1996
For Yamaha G16-A/G16-E Ultima 1996-2002
For Yamaha G2-A/G2-E 1985-1991
For Yamaha G3-A Sun Classic 1986
For Yamaha G3-E Sun Classic 1987
For Yamaha G5-A Sun Classic 1990-1995
For Yamaha G5-E Sun Classic 1990-1992
For Yamaha G6S 1970-1971
For Yamaha G7S 1972
For Yamaha G8-A/G8-EFleet Classic 1990-1994
For Yamaha G9-A/G9-E Fleet Master 1991-1995

Specification
Terminals: 4
Tactile point: Silver Tone
Potted Coil: Copper
Contact Material: Red Copper
Housing Material: Metal
Body: Zinc Plating Steel Case
Mounting Type: Flat 180 (F180)
High Current Stud: 5/16in
Low Current Stud: 0.19in
Length: 9cm / 3.54"
Mounting Hole to Hole Distance: 6cm /2.36"
Mounting Hole Width: 7mm / 0.28"
Bolt Center to Center Distance: 3cm / 1.18", 3.3cm / 1.30"

Electricity

Voltage: 12V
Resistance: 20
Work Current: 200A
Inrush Current: 250A
Duty Cycle: Continuous
Continuous Amps: 100

Feature:
Silver tone tactile point for stable performance
Durable zinc-plated steel and 180℃ copper wire to anti rusting, wear/heat resistance

Note:
This is non-OEM product, accessory only.
Check your old solenoid's mounting type and the length between mouting holes to avoid any mounting problem.
This is a continous duty solenoid, not a intermittent duty solenoid, continous type has lower power traveling and low withstand level compare to intermittent type.